The filter housing is usually placed underneath the vehicle, and the filter housing must be resistant to salt corrosion. Filters Diesel Systems Diesel fuel injection pump and is sucked through the swinging fine filter to the pump, high pressure regulator. At the bottom of the fuel pump is the primary filter for the detention of large dirt particles sizes. The filter element is located in a transparent casing, which also performs the function and dehumidified. Since the weight of water is greater than the weight of diesel fuel, then it is going and is visible at the bottom of a transparent body. Water must be disposed of in accordance with the instructions.
Finer filtration inherent 'Duplex' (double) filter, which has two filter elements, one for the detention of large particles, and another – for particles less than 2 microns – a thin filtration. Filter for diesel fuel is usually placed at the highest point in order to hold the air bubbles that prevent supply of diesel fuel into the system. To prevent this, you need to unscrew bolt at the top of the filter and let the air gathered. In some versions of fuel system is the automatic determination of the presence of water in the fuel; in achieving an acceptable level of water in the filter on dashboard warning light starts flashing. To reduce the possibility of condensation of water in the tank, we recommend completely fill the fuel tank at the end of the day or week, and the airspace above the fuel is minimal. The less air in the fuel tank, the less condensation may form. In the winter fuel suppliers offer a 'winter' diesel. A certain amount of fuel added to diesel fuel to reduce the possibility of the formation of paraffins (wax precipitation in the form of flakes).
The crystallization of paraffins at a temperature below-20oS or even higher, with chilly winds 20oS. The design of some filters heated components are installed and a thermostat that allows you to lower the temperature of the formation of paraffins. In the case of the formation of paraffins, it is necessary to replace all filters. Fuel filter element traps particles size from 5 to 10 microns.
The plant "Nevsky Filter" – is a leading domestic manufacturer of automotive filters and filter elements for cars and trucks. The company is part of the Industrial Group "Edelweiss" Russia's only industry holding company for the production of filters and filter elements. Beginning in 1997, the plant produces high-quality fuel, oil, air and cabin air filters to the European dizaynom.V Currently, the "Nevsky Filter" is equipped with the latest technology. The company has a modern high-tech equipment made in Japan, Germany, Italy and Korea. This is one of the most technically military industry enterprises. Filter assembly is carried out on automated production lines with minimal involvement of human resources and compliance with European quality standards. All products are factory specially adapted to Russian conditions of operation. Produced continuously filters are examined in the laboratory, which defines how well the filter material absorbs the contaminants contained in the fuel, oil or air.
The German unit PALAS-2000 allows you to control the quality of the used filter paper. The important fact is the high production company culture. More than 11 000 square meters. workshops covered special polyurethane nepylyaschimisya sexes. The company supplies its products to both primary and secondary automotive market in Russia and CIS countries. Today the plant is an official supplier fuel filter on a conveyor Ulyanovsk Automobile Plant (UAZ). Successfully tested and started to supply the pipeline Ulyanovsk Motor Works (UMP) of oil filters. The Minsk Motor Plant (MMZ) are test fuel and oil filters.
Also in full swing test cabin, fuel and oil filters at the Volga Automobile Plant (VAZ). Production Company "Nevsky Filter" has won multiple times tender for the supply of filters for passenger cars of the Ministry of Defense. The plant "Nevsky Filter" has been certified by QMS requirements of ISO 9001 in 2001. The document certifies that the filters are available, taking into account the regulatory documentation, and the state of production is stable and able to provide the appropriate level of product quality. The presence of such a document suggests that the work of the enterprise is organized accordance with international standards and found to be effective. After receiving the certificate of conformity with international quality standard ISO 9001, using best practices, new technologies and innovative approach to manufacturing products for the automotive industry, the company plans to implement in the future a strict policy of quality control aimed at the full satisfaction of customers.